[PDF and VCE] Latest DEA-5TT1 Exam Practice Materials Free Downloading
Attention please! Here is the shortcut to pass your DEA-5TT1 exam! Get yourself well prepared for the EMC Other Certification DEA-5TT1 Associate – Networking Exam exam is really a hard job. But don’t worry! We We, provides the most update DEA-5TT1 braindumps. With We latest DEA-5TT1 dumps, you’ll pass the EMC Other Certification DEA-5TT1 Associate – Networking Exam exam in an easy way
Visit our site to get more DEA-5TT1 Q and As:https://www.pass4king.com/dea-5tt1.html (61 QAs Dumps)
Question 1:
What are Network Address Translation (NAT) inside global addresses?
A. Addresses used by NAT router when sending frames to devices on the local network
B. Public IP addresses used by the local network to communicate with the Internet
C. Private IP addresses used by the local network
D. Pubic addresses used by other networks outside of the local network
Correct Answer: B
Question 2:
Which topology is considered a best practice when stacking switches?
A. Ring
B. Cascade
C. Serial
D. Daisy-chain
Correct Answer: A
Question 3:
Which port and protocol is used by NTP to communicate?
A. TCP port 123 for both the source and destination
B. TCP port 123 for the source and TCP port 80 for the destination
C. UDP port 123 for both the source and destination
D. UDP port 123 for the source and TCP port 80 for the destination
Correct Answer: C
Question 4:
At which layer of the OSI model is the Rapid Spanning Tree protocol used to prevent switching loops?
A. Physical
B. Network
C. Data Link
D. Transport
Correct Answer: C
Question 5:
Which field of the 802.3 frame is used by network interface cards to synchronize their receivers?
A. Start frame delimiter
B. Preamble
C. Cyclic redundancy check
D. Frame check sequence
Correct Answer: B
Question 6:
Which type of domains are connected by a Layer 2 switch?
A. Single collision domain and a single broadcast domain
B. Multiple broadcast domains and multiple collision domains
C. Multiple collision domains and a single broadcast domain
D. Single collision domain and multiple broadcast domains
Correct Answer: C
Question 7:
Which Layer 1 device can be used to enlarge the area covered by a single LAN segment?
A. Router
B. Repeater
C. Switch
D. NIC
Correct Answer: B
Question 8:
Which criteria is used to define an extended MAC ACL filter?
A. Destination MAC address and Ethernet frame type
B. Ethernet frame type and frame size
C. Destination TCP port number and source MAC address
D. Source and destination MAC addresses
Correct Answer: D
Question 9:
Which IPv4 address is in the same network as the IP address 182.15.24.40/23 and assignable to a host device?
A. 182.15.23.224
B. 182.15.25.0
C. 182.15.25.255
D. 182.15.26.10
Correct Answer: B
Question 10:
On which Dell EMC Networking switches can Multi-Chassis Link Aggregation (MLAG) be configured?
A. C9000 Series
B. N-Series
C. S-Series
D. Z-Series
Correct Answer: B
Question 11:
Which port type should be used for only VLAN-unaware devices?
A. Access port
B. General port
C. Hybrid port
D. Trunk port
Correct Answer: C
Question 12:
Which component translates data, signaling, and protocols to facilitate the data flow between the end device and the network?
A. Switch
B. Transceiver
C. NIC
D. Port
Correct Answer: B
Question 13:
When configuring a switch, which CLI mode only supports limited show commands?
A. EXEC
B. Maintenance
C. Configuration
D. EXEC Privilege
Correct Answer: A
Reference: https://www.dell.com/support/manuals/us/en/04/poweredge-fx2/dell fn ioa% 20config_9.8.0.0_pub-v1/cli-modes?guid=guid-aeb7d44d-2413-4da8-b8b9-2f8a26bad435andlang=en-us
Question 14:
A network administrator is troubleshooting an OSPF routing issue. There are two paths to a destination network from one switch. In addition, one path is comprised of four 1 Gb links. The other path is comprised of two 1 Gb and two 100 Mb links. The administrator ran several trace routes and notices that the packets are swapping back and forth between the two paths.
Which corrective action must be taken on the switch infrastructure to correct this issue?
A. Manually specify the OSPF Router ID on each switch within the path.
B. Break the paths into multiple OSPF areas.
C. Change the reference speed used by OSPF in cost calculations on all switches within the path.
D. Switch all routing protocols to RIPv2.
Correct Answer: C
Question 15:
How many total addresses for network, broadcast, and host are provided with the subnet mask 255.255.255.240?
A. 8
B. 16
C. 24
D. 48
Correct Answer: B
Visit our site to get more DEA-5TT1 Q and As:https://www.pass4king.com/dea-5tt1.html (61 QAs Dumps)
