Attention please! Here is the shortcut to pass your Mar 27,2022 Hotest NS0-505 exam questions exam! Get yourself well prepared for the NCIE-SAN ESeries Newest NS0-505 exam questions NetApp Certified Implementation Engineer – SAN ESeries exam is really a hard job. But don’t worry! We We, provides the most update NS0-505 actual tests. With We latest NS0-505 vce, you’ll pass the NCIE-SAN ESeries Newest NS0-505 vce NetApp Certified Implementation Engineer – SAN ESeries exam in an easy way

We Geekcert has our own expert team. They selected and published the latest NS0-505 preparation materials from Official Exam-Center.

The following are the NS0-505 free dumps. Go through and check the validity and accuracy of our NS0-505 dumps.If you need to check sample questions of the NS0-505 free dumps, go through the Q and As from NS0-505 dumps below.

Question 1:

What system file is used during the controller start-of-day sequence to determine various SCSI parameters and other host-type specific settings for an E-Series system? (Choose the best answer.)

A. Major Event Log

B. ESM Firmware


D. Unreadable Sectors Log

Correct Answer: C

Question 2:

What uses the Access Volume? (Choose the best answer.)

A. Legacy operating environments

B. XOR parity calculations

C. Asymmetric Logical Unit

D. Redundancy Check

E. SMagent

Correct Answer: E

Reference: 8)

Question 3:

Which three methods can be used to increase the space available to clients? (Choose three.)

A. Increase volume segment size

B. Convert RAID-6 volume group to RAID-5

C. Create new volume groups from unconfigured capacity

D. Fill empty drive slots in the array

E. Replace some HDD with SSD

Correct Answer: ACD

Question 4:

The decision to use FC or iSCSI on the 5500 Controller with a 4-port 16Gb/s FC or 10Gb/s iSCSI Optical SFP HIC (Host Interface Card) can be ___________. (Choose the best answer.)

A. ignored because both can be used at the same time

B. set at the factory, based on the order

C. based upon the SFP type

D. changed at any time by SANtricity

Correct Answer: C

Question 5:

What is the SANtricity Client? (Choose the best answer.)

A. A host I/O performance modeling interface

B. A GUI or CLI run on a host server used for storage system management

C. Inter-process communication that supports computer program subordinates

D. An OS-dependent collection of utilities for servers attached to SANtricity-managed storage systems

E. A host server process that enables storage system management with the storage data path

Correct Answer: D

Question 6:

What measurement refers to how much data can be handled in a given time period? (Choose the best answer.)

A. Read modify write

B. Throughput


D. Parity

E. I/O alignment

Correct Answer: B

Question 7:

Which interface is used to view and change the logical structure of a storage system? (Choose the best answer.)


B. Ldisk


D. Disk Manager


Correct Answer: E

Question 8:

Which storage manager feature scans the system for issues, reports them, and suggests procedures that will correct the issue?

A. Recovery guru

B. Event Log

C. Diagmon

D. Performance monitor

E. Storage array diagnostics

Correct Answer: B

Question 9:

Review the diagram.

Is this cabling correct or incorrect, and why? (Choose the best answer.)

A. The cabling is incorrect because the controllers are cabled from the host port.

B. The cabling is incorrect because it usesthe top-down bottom-up cabling method.

C. The cabling is correct because it follows the recommended E-Series cabling method.

D. The cabling is incorrect because they have been daisy-chained.

Correct Answer: D

Question 10:

What mechanism governs control of the E-Series storage premium features? (Choose the best answer.)

A. simple password system

B. special USB flash drive that must be inserted into the controllers

C. small toggle switches on the controller boards inside the system

D. key file obtained from vendor and passed to system via SANtricity

E. online database requiring the controllers to access the internet to activate features

Correct Answer: D


Question 11:

What happens if you choose one disk that has a capacity of 300 GB and five others that have a capacity of 900 GB for a volume group? (Choose the best answer.)

A. All disks are recognized as 900 GB in capacity.

B. All disks are recognized as 300 GB in capacity.

C. Each disk is recognized as its particular capacity.

D. Mixing disk capacities is not supported in E-Series volume groups.

Correct Answer: C

Reference: .20_Array_Management_Window_Help/capacity_allocation.html

Recommended Posts