Attention please! Here is the shortcut to pass your HPE6-A41 exam! Get yourself well prepared for the Aruba Certified Switching Associate (ACSA) HPE6-A41 Applying Aruba Switching Fundamentals for Mobility exam is really a hard job. But don’t worry! We We, provides the most update HPE6-A41 vce. With We latest latest HPE6-A41 dumps, you’ll pass the Aruba Certified Switching Associate (ACSA) HPE6-A41 Applying Aruba Switching Fundamentals for Mobility exam in an easy way
Download more HPE6-A41 exam questions and answers on:https://www.itcertbible.com/hpe6-a41.html (125 QAs Dumps)
Question 1:
Refer to the exhibit.
The network administrator enters this command: Switch# reload
Which software and configuration file will load?
A. software version KA.16.01 and config3
B. software version KA.15.15 and config2
C. software version KA.15.15 and config3
D. software version KA.16.01 and config1
Correct Answer: B
Question 2:
Refer to the exhibit.
What should the network administrator do to permit Switch-1 to route traffic from a client in 10.1.11.0/24 to a client in 10.1.12.0/24?
A. Enable proxy ARP.
B. Enable IP routing.
C. Configure a static route to 10.1.11.0/24 and a static route to 10.1.12.0/24.
D. Enable OSPF routing on VLAN 11 and on VLAN 12 in the same area.
Correct Answer: B
Question 3:
Refer to the exhibit.
Originally, all four switches had the same region configuration. VLAN 14 was added to Switch_D and then mapped to instance 2. How does this affect the MSTP topology?
A. Load sharing is lost, one of the uplinks is blocked for all traffic on Switch_C and Switch_D.
B. Load sharing is lost, one of the uplinks is blocked for all traffic on Switch_D
C. All connectivity is lost, both uplinks are blocked on Switch_D.
D. A Layer 2 loop exists and will cause sporadic connectivity issues.
Correct Answer: B
Question 4:
Refer to the exhibit.
The network administrator wants to place contractor clients and employee clients in different broadcast domains. How should the administrator achieve this goal?
A. Add a router in between Switch 1 and Switch 2. Configure a different subnet on each router interface.
B. Create two MSTP instances on each switch. Assign ports connected to contractor clients to one instance and ports connected to employee clients to the other instance.
C. Assign the switch ports connected to contractor clients to one VLAN and ports connected to employee clients to another VLAN. Extend the VLANs between the switches.
D. Create two device profiles. Apply one profile to ports connected to contractor clients, and apply the other profile to ports connected to employee clients.
Correct Answer: C
Question 5:
What is the relationship between a wireless client\’s data rate and the throughput for the client\’s traffic?
A. The throughput is 90 percent of the data rate.
B. The throughput is equal to the data rate multiplied by the connection time, minus the headers\’ bytes.
C. The throughput is less than the data rate and also depends on factors such as number of clients in the cell.
D. The data rate and the throughput are equivalent.
Correct Answer: B
Question 6:
Refer to the exhibit.
The network consists of two ArubaOS switches with routing disabled.
How should the network administrator configure the link between Switch A and Switch B to ensure that all hosts can communicate to all the other hosts within their respective VLANs?
A. tagged for VLAN 20 and tagged for VLAN 30
B. untagged for VLAN 10 and tagged for VLAN 30
C. tagged for VLAN 10 and tagged for VLAN 20
D. untagged for VLAN 10, untagged for VLAN 20, and tagged for VLAN 30
Correct Answer: C
Question 7:
A company has ArubaOS switches that are already configured to support the network. The company now wants to use Aruba AirWave to manage the switches. The network administrator creates a new group on Aruba AirWave, and then
discovers several ArubaOS switches that should belong to this group.
What is the best practice for the initial authorization of the switches in AirWave?
A. Authorize the switches in Monitor Firmware Updates only mode.
B. Authorize the switches and immediately change the scan set credentials to match the credentials on the switches.
C. Authorize the switches and immediately change the global communication settings to match the credentials on the switches.
D. Authorize the switches in Managed Read/Write mode.
Correct Answer: D
Question 8:
A network administrator configures MSTP on an ArubaOS switch. The administrator wants to ensure that this switch is always the root for instance 1. What should the administrator do to accomplish this?
A. Specify priority 15 for spanning tree instance 1.
B. Specify spanning tree cost 0 on all switch ports that connect to other switches that use instance 1.
C. Specify priority 0 for spanning tree instance 1.
D. Specify spanning tree cost 15 on all switch ports that connect to other switches that use instance 1.
Correct Answer: C
Question 9:
A retail company needs a quick way to deploy network infrastructure to new sites.
Which Aruba solutions provide Zero Touch Provisioning (ZTP) for Aruba Instant APs (IAPs) and ArubaOS switches?
A. Aruba AirWave and Aruba Activate
B. Aruba Meridian and Aruba ALE
C. Aruba AirWave and Aruba Central
D. Aruba Activate and Aruba Meridian
Correct Answer: A
Question 10:
Refer to the exhibit.
Exhibit 1.
Exhibit 2.
The administrator enters the show spanning-tree instance 2 command on Switch-3 and sees the output shown in Exhibit 2. What could explain the output results?
A. Switch-1 has a lower MAC address than Switch-2.
B. Switch-1 has a higher MAC address than Switch-2.
C. Switch-3 filters BPDUs on port 26.
D. Switch-3 has incompatible MSTP region settings with other switches.
Correct Answer: D
Question 11:
Managers log in to an ArubaOS switch with SSH.
What does SSH require to authenticate the switch to the SSH client and set up a secure session?
A. an SSH authorized user key, managed by the ip ssh public-key commands
B. a username and password set with the password manager command
C. an SSH key, managed by the crypto key ss commands.
D. a self-signed certificate configured with the crypto key commands
Correct Answer: B
Reference: http://h20564.www2.hpe.com/hpsc/doc/public/display?docId=mmr_kc-0134172
Question 12:
Refer to the exhibit.
The network administrator enters this command:
Switch(config)# ip route 172.16.2.0/30 192.168.1.100 metric 1 distance 1
Why does this route fail to appear in the IP routing table?
A. Its prefix length is invalid.
B. Its next hop is unreachable.
C. Its administrative distance is the same as an existing static route.
D. Its metric is the same as an existing static route.
Correct Answer: B
Question 13:
Refer to the exhibit. Exhibit 1.
Exhibit 2.
Which devices can communicate with each other at Layer 2?
A. Devices 1 and 2 can communicate at Layer 2; Devices 3 and 4 can communicate at Layer 2.
B. Devices 2 and 3 can communicate at Layer 2.
C. Devices 1 and 4 can communicate at Layer 2.
D. Devices 1 and 4 can communicate at Layer 2; Devices 2 and 3 can communicate at Layer 2.
Correct Answer: C
Question 14:
Refer to the exhibit. Exhibit 1.
Exhibit 2.
The routing configuration must support this behavior:
Server 1 and Server 2 communicate over Link 1 when Link 1 is up.
If Link 1 fails, Server 1 and Server 2 can continue to communicate over the path through Switch-3.
What must the network administrator change to meet these criteria?
A. On Switch 3, add a route to 192.168.2.0/24 through 192.168.1.9 and a route to 192.168.3.0/24 through 192.168.1.5.
B. On Switch-1, Switch-2, and Switch-3, change the next hop in each static route to specify an IP address that exists on that switch.
C. On Switch-1, raise the administrative distance for the second route to 192.168.3.0/24; on Switch-2, raise the administrative distance for the second route to 192.168.2.0/24
D. On Switch-1, add a route to 192.168.1.8/30 through 192.168.0.3; on Switch-2, add a route to 192.168.1.4/30 through 192.168.1.1; on Switch-3, add a route to 192.168.1.0/30 through 192.169.1.4.
E. On Switch-1, add a route to 192.168.1.8/30 through 192.168.1.2; on Switch-2, add a route to 192.168.1.4/30 through 192.168.1.1; on Switch-3, add a route to 192.168.1.0/30 through 192.168.1.4.
Correct Answer: C
Question 15:
A network administrator plans to set up a WLAN on an Aruba Instant cluster. The WLAN uses WPA/WPA2 Enterprise security. The administrator wants no authenticate users locally on the cluster. How should the administrator configure me credentials?
A. Add a user account for each employee to the cluster internal server database.
B. Import authorized device MAC addresses to the cluster.
C. Implement a shared secret or password in the cluster WLAN settings.
D. Set up an external RADIUS server for authorization.
Correct Answer: D
Download more HPE6-A41 exam questions and answers on:https://www.itcertbible.com/hpe6-a41.html (125 QAs Dumps)
