HP ATP Jan 15,2022 Hotest HP0-Y52 vce dumps easy pass guidance: Preparing for HP HP ATP Hotest HP0-Y52 practice exam is really a tough task to achieve. However, Geekcert provides the most comprehensive PDF and VCEs, covering each knowledge points required in the actual Newest HP0-Y52 vce exam.
Geekcert- reliable HP0-Y52 certifications expert on HP0-Y52 exam study guide providing. Geekcert – leader of HP0-Y52 certifications, latest dumps, guaranteed pass. pass your HP0-Y52 exam in 1 day with Geekcert. Geekcert – leading source of HP0-Y52 certification exam learning/practice. Geekcert – HP0-Y52 certification exams – original questions and answers – success guaranteed.
We Geekcert has our own expert team. They selected and published the latest HP0-Y52 preparation materials from HP Official Exam-Center: https://www.geekcert.com/hp0-y52.html
The following are the HP0-Y52 free dumps. Go through and check the validity and accuracy of our HP0-Y52 dumps.These questions are from HP0-Y52 free dumps. All questions in HP0-Y52 dumps are from the latest HP0-Y52 real exams.
Question 1:
Two switches are members in an active Intelligent Resilient Framework (IRF) virtual device. A network administrator joins a third switch to the IRF virtual device. Which switch is now the master?
A. The current master of the IRF virtual device always remains the master.
B. The switch with the lowest member ID always becomes the master.
C. The switch with the lowest priority value always becomes the master.
D. The switch with the highest priority value always becomes the master.
Correct Answer: D
Question 2:
A network administrator configures OSPF in an HP ProVision based network. The administrator is concerned that a rogue device might connect to an access layer switch and introduce OSPF routes to the company\’s routing topology.
The access VLANs do not contain additional routers.
Which configuration should the administrator apply for these access VLANs to prevent them from forming an adjacency with rogue devices?
A. router ospfno vlan neighbor-adjacency
B. route spfip silent-vlan
C. router ospf passive-vlan
D. vlan ip ospf passive
Correct Answer: D
Question 3:
A company requires switches to use Multiple Spanning Tree Protocol (MSTP) instead of Rapid Spanning Tree Protocol (RSTP), so that the switches can forward traffic on more than one switch-to-switch link. How does the administrator set up the solution to meet this requirement?
A. Configure every switch with a unique bridge priority in the IST, which is also called spanning tree instance 0.
B. Ensure that switches use the 802.3t standard costs instead of the legacy costs.
C. Set the same spanning tree cost on all redundant links on a switch.
D. M different VLANs to different instances, and make a different switch root bridge in each instance.
Correct Answer: D
Question 4:
An HP Comware switch should send messages to an SNMP server when various events occur. What is one step in the configuration of this feature?
A. Enable SSH on the switch, and create a user account to match settings on the SNMP server.
B. Set the SNMPv2 read-write community string to match the string on the SNMP server.
C. Enable logging to the console globally.
D. Specify an SNMP trap server with the SNMP server IP address and community string.
Correct Answer: D
Question 5:
A network administrator configures several HP Comware switches to be part of a single Intelligent Resilient Framework (IRF) virtual device. What is correct about the domain and member IDs in this configuration?
A. The switches have different domain IDs and different member IDs.
B. The switches have the same domain ID and the same member ID.
C. The switches have the same domain ID and different member IDs.
D. The switches have different domain IDs and the same member ID.
Correct Answer: C
Question 6:
What is one difference between Network Segment-based discovery and ARP-based discovery on HP Intelligent Management Center (IMC)?
A. With Network Segment-based discovery, network device SNMP settings must match SNMP settings on IMC. With ARP-based discovery, only ARP settings must match.
B. With Network Segment-based discovery, IMC can discover multiple devices. With ARP- based discovery, IMC can only discover one device; the administrator must re-run ARP- based discovery to discover a second device.
C. With Network Segment-based discovery, the administrator enters a range of IP addresses to discover. With ARP-based discovery, the administrator enters one seed IP address, and IMC dynamically learns more IP addresses to discover.
D. With Network Segment-based discovery, IMC can discover Layer 3 devices. With ARP- based discovery, IMC can discover only Layer 2 devices.
Correct Answer: C
Question 7:
Refer to the exhibits.
Exhibit 1
Exhibit 2
A network administrator executes the show vlan commands and sees the output shown in the exhibits. How must the administrator configure a connected port on an HP Comware switch?
A. as a trunk port
B. as an access port
C. as an untagged port
D. as a mixed port
Correct Answer: A
Question 8:
Refer to Exhibit.
The server shown in the exhibit requires redundant links, and The link aggregation should use LACP. What should the administrator configure on the 1RF virtual switch?
A. a bridge aggregation interface that uses static link aggregation mode
B. a bridge aggregation interface that uses dynamic link aggregation mode
C. two interfaces that are set to trunk for the port-link type
D. two interfaces that are set to hybrid for the port-link type
Correct Answer: B
Question 9:
What is one reason to access the extended boot menu on an HP Cornware switch?
A. To access the switch CLI when you have forgotten the password
B. To set up the switch to be managed by HP Intelligent Management Center (IMC).
C. To configure the switch initial IP address settings
D. To configure the switch to implement Intelligent Resilient Framework (IRF)
Correct Answer: A
Question 10:
Refer to the exhibits.
Exhibit 1
Exhibit 2
PC1 cannot reach PC2. Based on the exhibits, what could be causing this error?
A. PC1 has the wrong IP address for its default gateway setting.
B. Router A has a direct route, instead of a static route, to 10.1.10.0/24.
C. The next hop address for the 10.1.20.0/24 route is incorrect.
D. Router A has an invalid subnet mask for the VLAN 1 subnet.
Correct Answer: B
Question 11:
Refer to the exhibit.
A network administrator is upgrading the operating system on an HP Comware switch. When copying the new image from a TFTP server to the flash of the switch, the process fails because there is not enough flash to store the new operating system. The new operating system is 3.2MB in size. The administrator then executes the commands shown in the exhibit above.
Which action should the administrator perform to solve this problem?
A. Execute the reset recycle-bin command, and perform the TFTP transfer again.
B. Execute the clear flash command, and perform the TFTP transfer again.
C. Reformat flash, and perform the TFTP transfer again.
D. Execute the delete old.app command, and perform the TFTP transfer again.
Correct Answer: A
Question 12:
Which method of link aggregation do both HP ProVision and Comware switches support?
A. Static LACP
B. Fast Ethernet
C. Dynamic LACP
D. Distributed Trunking
Correct Answer: A
Question 13:
An HP switch learns identical valid routes with different protocols. How does the switch choose which route to add to its IP routing table?
A. It adds the route with the highest administrative distance, or route preference.
B. It adds the route with the highest cost.
C. It adds the route with the lowest cost.
D. It adds the route with the lowest administrative distance, or route preference.
Correct Answer: D
Question 14:
Refer to the exhibit.
What does the output indicate about GE1/0/1?
A. The interface accepts untagged traffic, which it assigns to VLAN 1. It drops traffic that is tagged for VLANs 1, 10, and 20.
B. The interface accepts untagged traffic, which it assigns to VLAN 1. It also accepts traffic that is tagged for VLANs 10 and 20.
C. The interface accepts untagged traffic, which it assigns to VLAN 1. It accepts traffic that is tagged for any VLAN between 10 and 20.
D. The interface does not accept untagged traffic. It accepts traffic that is tagged for VLANs 1, 10, and 20.
Correct Answer: B
Question 15:
Refer to the Exhibit.
A network administrator has configured an HP Comware switch to act as the DHCP server for VLAN 12, but the switch is not responding to clients\’ DHCPDISCOVER messages. Based on the exhibit, what is the problem with the DHCP configuration?
A. DHCP is not enabled globally on the switch.
B. DHCP relay is not enabled on VLAN 12.
C. DHCP server is not enabled on VLAN 12.
D. DHCP server ping timeout setting is set too high.
Correct Answer: A
